Industry Indices
← Research & analysis
Pool equipment

Pool equipment

Original research analysis

AO Buying Guide | Competition & Public Swimming Pool Systems: Verifying Pool Shells, Filtration, Starting Blocks and Timing Touchpads

Swimming facilities typically span four distinct supplier types: modular pool-shell builders, filtration and dosing integrators, deck competition hardware makers, and electronic timing providers. Drawing on 68 recorded pool products, World Aquatics partner disclosures, and GB 37488 water-quality rules, this guide maps critical interface specifications.

Record date (source acquisition dates below) Nov 17, 2026 · Original editorial and source-scope review · Complete bilingual article and abstracts

Scope

Intended for campus natatoriums, municipal swimming centers, and competition pool equipment procurement; does not substitute for licensed MEP engineering design or accredited water-quality testing.

1. Separate Four Distinct Supplier Scopes Before Writing Tender Specs

A frequent procurement mistake in natatorium projects is bundling shell construction, mechanical-room filtration, deck hardware, and electronic timing under a single vague 'pool equipment' specification. Cross-checking World Aquatics partner disclosures and AO Ranking's 68 recorded pool equipment records shows four distinct engineering scopes:

SubsystemRepresentative Library & Federation EntitiesCore Recorded ParametersCritical Interface Checks
Modular Pool Shell & GutterMyrtha Pools / modular stainless buildersLaminated stainless panel gauge, overflow channel profile, length tolerance (mm)Deck anchor loads; net lane length after touchpad installation
Filtration & Chemical DosingDaisile / Pentair / Waterco / ChemtrolFilter tank diameter, filtration area (m²), filtration rate (m/h), flow (m³/h), ORP/pH controller rangePlant-room headroom & doorway clearance, backwash drain sizing, 3-phase power
Deck Competition HardwareAnti Wave / Duraflex / starting block makersBlock top dimensions & wedge angle, wave-quelling disc diameter (110mm/150mm), 304 vs. 316L stainless gradeWall cup anchor elevation, starting-block bolt pattern, chloramine corrosion resistance
Timing Touchpads & StartOMEGA (Swiss Timing)Touchpad dimensions (e.g. 2400×900×10mm or 1892×900×10mm), actuation force, low-voltage busGutter bracket geometry; 10mm per-wall length allowance so net course stays legal
2 section citations

2. Filtration Tanks: Lock Down Filtration Area and Velocity Together

Across commercial sand filters recorded in AO Ranking's product library, official spec tables list tank diameter (mm), filtration area (m²), design filtration velocity (m/h), and rated flow (m³/h) together. A 1200mm tank (~1.13 m² area) yields ~34 m³/h on paper at 30 m/h high-rate velocity, yet delivers only 22–28 m³/h at the 20–25 m/h medium velocity preferred for competition or heavy-bather public pools.

Tender documents should therefore never specify flow rate alone. Always lock down minimum total filtration area (m²), maximum design filtration velocity (m/h), working pressure rating (e.g., 2.5 bar vs. 4.0 bar), and turnover period (hours) so mechanical sizing aligns with GB 37488-2019 turbidity and disinfectant uniformity limits.

1 section citations

3. Net Course Length vs. Touchpad Thickness: Avoiding Costly Civil Rework

In the OMEGA OCP5 swimming touchpad datasheet archived in our library, nominal panel thickness is 10 mm (offered in 2400×900×10 mm and 1892×900×10 mm models). If a 50m or 25m competition pool is tiled to an exact 50.000m wall-to-wall finish without touchpad allowance, hanging one or two 10mm touchpads reduces net lane length below federation minimums.

Project teams must confirm upfront whether single-end or double-end touchpads and movable bulkheads will be used, building explicit thickness allowances into pool-wall tolerances.

2 section citations

4. Chloramine Corrosion Protection for Indoor Natatorium Hardware

Indoor heated natatoriums expose deck and submerged hardware to warm chloramine vapor year-round. Recorded spec sheets for ladders, lane-line tensioners, anchor cups, and underwater luminaires explicitly distinguish AISI 304 from AISI 316/316L stainless steel. For indoor chlorinated pools, salt-chlorinator systems, or coastal venues, specify 316/316L stainless steel with mill certificates for all anchors, hooks, fasteners, and rails to prevent early pitting corrosion.

1 section citations

5. Delivery and Commissioning Verification Checklist

  • Verify filter tank nameplates for filtration area (m²), maximum working pressure, and hydrostatic test certificates.
  • Check probe replacement intervals and calibration procedures for online pH, ORP/free-chlorine, turbidity, and temperature controllers.
  • Inspect starting-block non-slip tops, backstroke ledge adjustment mechanisms, and lane-line tensioner safety covers.
  • For competition venues, survey and log exact lane lengths before filling, after filling, and with timing touchpads mounted.
2 section citations

Sources & retrieval dates

Documented source dates

  1. Source acquisition record